How to identify cable fault points without using a cable fault tester

2022/06/09

Author: Noyafa–Cable Locator Suppliers

Identify the fault point How to identify the fault point of the cable without the cable fault tester Identify the fault point The value of liquidity is small, and the common problems are far behind; 4. The amount of short-speed overcurrent is the same as the power trip, and the common problems are located in the middle of the line. 5. The area of ​​the line caused by the safety production accident is different, and the posture of the relay protection device is different. Electric water output interruption maintenance attitude trip: Electric water output interruption generally causes short-circuit faults in the large operation mode of the system. When short-circuit faults are common faults, the maintenance level is large, accounting for about 50% of the total length of the line.

When the line is in the small operation mode, the maintenance level is small, accounting for 15% to 20% of the total length of the line. Therefore, the attitude tripping of the electric water output protection device indicates that the common problem is generally located in the front-end development of the line (near the distribution station side). 6. Overcurrent flow maintenance The attitude of the equipment is tripped: the maintenance level of the overcurrent total flow maintenance is 100% of the line being maintained.

However, in general, overcurrent maintenance machines and equipment are also equipped with time-delay relays. When used in conjunction with quick-break protection devices, attitude trips are generally only caused when common problems are caused in the rear of the line. 7. Maintenance and maintenance of electric water output interruption and overcurrent flow maintenance In addition to attitude tripping: This kind of situation generally indicates that the common problem points are located at the mutual level of quick-break maintenance and overcurrent flow maintenance, and most of the common problem points are located in the middle of the line. Difficult problems After the knife switch of the distribution station trips, immediately investigate the posture of the relay protection device.

According to the posture type and characteristics of relay protection equipment and equipment, the characteristics and levels of common problems are preliminarily agreed. How to identify the cable fault point without the cable fault tester Identify the fault point Shenzhen Noyafa Electronic Technology Co., Ltd.

CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry

Send your inquiry

Choose a different language
English
Magyar
Ελληνικά
한국어
Türkçe
русский
italiano
Español
Português
Polski
français
Deutsch
日本語
Nederlands
Tiếng Việt
ภาษาไทย
Latin
العربية
简体中文
繁體中文
Afrikaans
አማርኛ
Azərbaycan
Беларуская
български
বাংলা
Bosanski
Català
Sugbuanon
Corsu
čeština
Cymraeg
dansk
Esperanto
Eesti
Euskara
فارسی
Suomi
Frysk
Gaeilgenah
Gàidhlig
Galego
ગુજરાતી
Hausa
Ōlelo Hawaiʻi
हिन्दी
Hmong
Hrvatski
Kreyòl ayisyen
հայերեն
bahasa Indonesia
Igbo
Íslenska
עִברִית
Basa Jawa
ქართველი
Қазақ Тілі
ខ្មែរ
ಕನ್ನಡ
Kurdî (Kurmancî)
Кыргызча
Lëtzebuergesch
ລາວ
lietuvių
latviešu valoda‎
Malagasy
Maori
Македонски
മലയാളം
Монгол
मराठी
Bahasa Melayu
Maltese
ဗမာ
नेपाली
norsk
Chicheŵa
ਪੰਜਾਬੀ
پښتو
Română
سنڌي
සිංහල
Slovenčina
Slovenščina
Faasamoa
Shona
Af Soomaali
Shqip
Српски
Sesotho
Sundanese
svenska
Kiswahili
தமிழ்
తెలుగు
Точики
Pilipino
Українська
اردو
O'zbek
Xhosa
יידיש
èdè Yorùbá
Zulu
Current language:English