How should the double gun cable stab device be used?

2022/07/20

Author: Noyafa–Cable Tester Manufacturer

Question: How should the dual gun cable piercer be used? Answer: The double-gun cable piercing device is mainly used to pierce the cable. It has many advantages such as convenience, safety and fast speed. It has been widely praised by the majority of electric power workers. How should the device be used? Answer: The double-gun cable piercer is mainly used to pierce the cable. It has many advantages such as convenience, safety and fast speed. It has been widely praised by the majority of electric power workers. At the same time, the improper operation of the piercer often causes accidents. Accidents occur, so it is very important to use the stabbing device correctly. Use the cable card device to fasten the pre-tied position of the pre-tied cable. In addition, the first gun and the second gun should be installed with a deflection of 30-40 degrees to ensure the reliability of the stabbing. Insert the nail from the front end of the front barrel with a through needle and press it until it is in contact with the piston rod.

Then install the nail bullet, and then install the nail gun. Note: The nail gun can be installed at any angle on site, but the muzzle must be aligned with the pre-wired cable, and there must be no other cables on the other side of the muzzle, so as to avoid accidents caused by piercing other cables at the same time. When piercing the cable, one end of the ground wire needs to be connected to the screw of the cable device, and the other end is grounded or the system ground.

Use the control wire to connect the nail gun to the controller. The installation of the two nail guns is the same. The left side of the controller is the first output, and the right side is the second output. The cable identification instrument, if only a single point of piercing is performed , the nailer should be connected to the second output port. press“choose”key, the screen will switch between timing mode and remote control mode; press in the desired mode“confirm”key to enter the selected mode, ? Double gun cable piercer press the select key to exit, if prompted on the display“After the operation, how to use it”, please wait for a period of time (more than 10S) before disassembling the device. (Please use an electroscope that corresponds to the power supply level of the cable, and remove the device after confirming that the nailer is not electrified.

) If you choose to enter the remote control mode, after the voice prompts, please stay away from the scene, and press the two keys of the remote control at the same time (to ensure reliable reception, the transmitting antenna of the remote control needs to be completely pulled out). If the nail bomb explodes twice and the nail is shot, the stab is successful; the display prompts“After the operation is completed, please ensure that the cable is not charged and then disassemble the device”, please wait for a period of time (more than 10S) before disassembling the device. (Please use an electroscope that corresponds to the power supply level of the cable, and remove the device after confirming that the nailer is not electrified.

) If the double-gun cable stabbing device is used improperly, it will cause serious consequences, so the user needs to read the product instruction manual thoroughly before using it, and use it in strict accordance with the requirements and specifications of the manual, so as to achieve the equipment should have the effect.

CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry

Send your inquiry

Choose a different language
English
Magyar
Ελληνικά
한국어
Türkçe
русский
italiano
Español
Português
Polski
français
Deutsch
日本語
Nederlands
Tiếng Việt
ภาษาไทย
Latin
العربية
简体中文
繁體中文
Afrikaans
አማርኛ
Azərbaycan
Беларуская
български
বাংলা
Bosanski
Català
Sugbuanon
Corsu
čeština
Cymraeg
dansk
Esperanto
Eesti
Euskara
فارسی
Suomi
Frysk
Gaeilgenah
Gàidhlig
Galego
ગુજરાતી
Hausa
Ōlelo Hawaiʻi
हिन्दी
Hmong
Hrvatski
Kreyòl ayisyen
հայերեն
bahasa Indonesia
Igbo
Íslenska
עִברִית
Basa Jawa
ქართველი
Қазақ Тілі
ខ្មែរ
ಕನ್ನಡ
Kurdî (Kurmancî)
Кыргызча
Lëtzebuergesch
ລາວ
lietuvių
latviešu valoda‎
Malagasy
Maori
Македонски
മലയാളം
Монгол
मराठी
Bahasa Melayu
Maltese
ဗမာ
नेपाली
norsk
Chicheŵa
ਪੰਜਾਬੀ
پښتو
Română
سنڌي
සිංහල
Slovenčina
Slovenščina
Faasamoa
Shona
Af Soomaali
Shqip
Српски
Sesotho
Sundanese
svenska
Kiswahili
தமிழ்
తెలుగు
Точики
Pilipino
Українська
اردو
O'zbek
Xhosa
יידיש
èdè Yorùbá
Zulu
Current language:English