Do you know the key points of using the cable fault tester?

2022/07/12

Author: Noyafa–Cable Tester Manufacturer

Question: Do you know the main points of the cable fault tester? Answer: The cable fault tester is a comprehensive set of equipment, which can be used for open circuit, short circuit, grounding, low resistance, high resistance flashover and high resistance leakage of power cables Fault test, and the same question: Do you know the main points of the cable fault tester? Answer: The cable fault tester is a comprehensive set of equipment, which can be used for power cable open circuit, short circuit, grounding, low resistance, high resistance flashover It can also test the open-circuit and short-circuit faults of coaxial communication cables and local telephone cables. It can also test the cable path, burial depth, and radio wave speed, verify the cable length, etc., and can establish a cable file to facilitate Daily maintenance management. In the process of use, we need to pay attention to the following points to ensure the stability of the equipment, including: 1. During the pulse method test, pay attention to throw away all the equipment in the office and measure on the outside line. 2. When using the flashover method to test, the trigger working mode switch must be placed in“Flashover”Location.

3. Pay attention to personal safety and equipment safety when using the direct flash method or the dash flash method for testing. The ground wire must be connected. 4. After the flashover test is over, cut off the power supply, remove the connecting wire between the instrument and the high-voltage test device, and then discharge the stored charge of the high-voltage capacitor and cable.

When discharging, a current limiting resistor R should be added to limit the discharge current to discharge the current slowly. After the voltage on the capacitor is reduced, the resistance in the discharge circuit to the ground is zero, and the instantaneous discharge current can be as high as several hundred amperes, which will cause serious damage. equipment or personal accident. 5. During the direct-flash test, attention must be paid to monitoring the leakage current of the fault. If the current suddenly increases and the fault flashover has not occurred, the test voltage should be lowered immediately and the flash-over test should be used instead.

CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry

Send your inquiry

Choose a different language
English
Magyar
Ελληνικά
한국어
Türkçe
русский
italiano
Español
Português
Polski
français
Deutsch
日本語
Nederlands
Tiếng Việt
ภาษาไทย
Latin
العربية
简体中文
繁體中文
Afrikaans
አማርኛ
Azərbaycan
Беларуская
български
বাংলা
Bosanski
Català
Sugbuanon
Corsu
čeština
Cymraeg
dansk
Esperanto
Eesti
Euskara
فارسی
Suomi
Frysk
Gaeilgenah
Gàidhlig
Galego
ગુજરાતી
Hausa
Ōlelo Hawaiʻi
हिन्दी
Hmong
Hrvatski
Kreyòl ayisyen
հայերեն
bahasa Indonesia
Igbo
Íslenska
עִברִית
Basa Jawa
ქართველი
Қазақ Тілі
ខ្មែរ
ಕನ್ನಡ
Kurdî (Kurmancî)
Кыргызча
Lëtzebuergesch
ລາວ
lietuvių
latviešu valoda‎
Malagasy
Maori
Македонски
മലയാളം
Монгол
मराठी
Bahasa Melayu
Maltese
ဗမာ
नेपाली
norsk
Chicheŵa
ਪੰਜਾਬੀ
پښتو
Română
سنڌي
සිංහල
Slovenčina
Slovenščina
Faasamoa
Shona
Af Soomaali
Shqip
Српски
Sesotho
Sundanese
svenska
Kiswahili
தமிழ்
తెలుగు
Точики
Pilipino
Українська
اردو
O'zbek
Xhosa
יידיש
èdè Yorùbá
Zulu
Current language:English